Investigation of the effect of micro-fillers on Viscoelastic and Erosion wear Characteristics of PTFE composites
Authors:
Gamini Suresh, Lakshmi Srinivas Ch, M Chandra SekharDOI NO:
https://doi.org/10.26782/jmcms.2020.07.00061Abstract:
Polytetrafluorethylene (PTFE)is one type of the most prominent semi-crystalline engineering thermo-plastics. The functional properties of PTFE are enhanced with the addition of micro-fillers inorder to increase the utility of the composites. In the current work, three types of industrial Teflon composites with micro-fillers viz. 25% by weight of glass fibers, 25% by weight of carbon fibers, and 25% by weight of graphite along with neat PTFE were used to investigatethe viscoelastic and erosion wear characteristics. From the Dynamic Mechanical Analysis (DMA) graphs, it was observed that PTFE with 25% by weight of GF has shown peak viscoelastic characteristicsinthree-point bending mode. The viscoelastic properties such asstorage modulus of 1 GPa, loss modulus of 84 MPa and a tand of 0.137 respectively at 1400 C were observed from the DMA plots for the sample (PTFE+25%GF).Also, the erosion wear behavior of the same sample has shown good resistance at 1.5 bar and 90o impingement angle respectively due to the addition of glass fiber micro-filler.Keywords:
PTFE composites,glass fibers,carbon fibers,graphite,viscoelastic properties,erosion wear,Refference:
I. A. Patnaik, A. Satapathy, S. S. Mahapatra, and R. R. Dash, “A modeling approach for prediction of erosion behavior of glass fiber-polyester composites,” J. Polym. Res., vol. 15, no. 2, pp. 147–160, 2008.
II. A. Patnaik and A. Satapathy, “Erosion Wear Response of Flyash-Glass Fiber-Polyester Composites : A Study using Taguchi Experimental Design,” vol. 4, no. 2, pp. 13–28, 2009.
III. A. Patnaik, A. Satapathy, N. Chand, N. M. Barkoula, and S. Biswas, “Solid particle erosion wear characteristics of fiber and particulate filled polymer composites: A review,” Wear, vol. 268, no. 1, pp. 249–263, 2010.
IV. A. Rout, A. Satapathy, S. Mantry, A. Sahoo, and T. Mohanty, “Erosion Wear Performance Analysis of Polyester-GF-Granite Hybrid Composites using the Taguchi Method,” Procedia Eng., vol. 38, pp. 1863–1882, 2012.
V. G. Suresh, V. Vasu, and G. R. Rao, “Optimization of Input Parameters on Erosion Wear Rate of PTFE / HNT filled nanocomposites,” pp. 2–9, 2016.
VI. H. E. Sliney, L. Research, C. Cleveland, and F. J. Williams, “NASA Technical Memorandum 82779.”
VII. J. K. Lancaster, “Composites for Aerospace Dry Bearing Applications,” in Composite Materials Series, vol. 1, no. C, Elsevier, 1986, pp. 363–396.
VIII. K. Friedrich, Friction and Wear of Polymer Composites. Elsevier Science, 1986.
IX. S. B. Chaudhari and S. P. Shekhawat, “Wear Analysis of Polytetrafluoroethylene (PTFE) and it’s Composites under Wet Conditions.”
X. S. Kumar, B. K. Satapathy, and A. Patnaik, “Viscoelastic interpretations of erosion performance of short aramid fibre reinforced vinyl ester resin composites,” J. Mater. Sci., vol. 46, no. 23, pp. 7489–7500, 2011.
XI. W. Brostow, H. E. Hagg Lobland, and M. Narkis, “Sliding wear, viscoelasticity, and brittleness of polymers,” J. Mater. Res., vol. 21, no. 09, pp. 2422–2428, 2006.
XII. X. Cheng, Y. Xue, and C. Xie, “Tribological investigation of PTFE composite filled with lead and rare earths-modified glass fiber,” Mater. Lett., vol. 57, no. 16–17, pp. 2553–2557, May 2003.